旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � 32-Bit PCI Ethernet Adapter � � NETWORK TESTING PROGRAM (DIAG) USER GUIDE � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� �袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴敲 � Release History � 勁袴袴袴袴袴藁袴袴袴袴藁袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴� � date � version � description � 勁袴袴袴袴袴誥袴袴袴袴誥袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴� � 02-18-1994 � v1.00 � 1. New release. � � � � � � 11-12-1994 � v1.03 � 1. Support multiple adapters. � � � � 2. Modify the medium selection method.� � � � � � 01-09-1995 � v1.04 � 1. Support medium auto-sense function.� � � � 2. Reset NIC before each functional � � � � testing. � � � � � � 05-24-1995 � v2.00 � 1. Support fast Ethernet adapter. � 훤袴袴袴袴袴菰袴袴袴袴菰袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴� 1. The 32-Bit PCI Ethernet Adapter Network Testing Program - DIAG The 32-Bit PCI Ethernet driver disk contains a network testing program called DIAG. Run this program to check if your adapter is properly installed. The DIAG program supports for the following PCI LAN adapters: 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � Product Name Product Number � 쳐컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� � 32-Bits PCI-bus Ethernet Adapter ETH_32 � � 32-Bits PCI-bus fast Ethernet Adapter ETH_32 100TX � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� This DIAG program performs the following tests: a. Configuration Test b. I/O Test c. ID Test d. Internal Loopback Test e. External Loopback Test f. Interrupt Test g. Network Function Test 2. Test Requirements To run DIAG, you need at least two workstations, each with an installed 32-bit PCI Ethernet adapter. You should run the program in both workstations, one after the other. If you want to test 100Mbps fast Ethernet operation, you must have at least two workstations each with an installed 32-bit fast Ethernet adapter. 3. Running the DIAG Program Insert the 32-bit PCI Ethernet Adapter driver disk into your flopppy drive (A:), and type: A:\> CD DIAG A:\DIAG> DIAG ---------------------------------------------------------------------- 3.0. When you run DIAG, it searches the 32-bit PCI (fast) Ethernet adapters on your PC. If your PC does not support PCI BIOS, or if no the 32-bit PCI (fast) Ethernet adapters exists on your PC, DIAG will display an error message, Otherwise, it will display information of all the PCI network adapters found existing on your PCI machine. These information are: Ethernet address, IRQ used, I/O port used, and the predefined media-type (AUTO, means media-type AUTO-sensing). You can use the UP and DOWN arrow keys to select the adapter to test, or the RIGHT and LEFT arrow keys to select the media-type. The 32-bit PCI Ethernet adapter supports three media-types: 1. AUTO 2. TP 3. BNC; while the 32-bit PCI Fastnet adapter supports four media-types; they are: 1. AUTO 2. TP 100Mbps 3. TP 10Mbps 4. BNC 10Mbps. Note that AUI port is not supported for this version of 32-bit PCI adapters. Press to confirm selection and start the testing process, or press to exit the DIAG program. 3.1. The screen will display the status of the testing. The screen display on your monitor is similar to Figure 1. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴커 � 32-bit PCI-bus Ethernet Adapter Network Testing Program � � Version 2.00 Release Date: May. 24, 1995 � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴켸 같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같 같같같같같같같같같같같�袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴뺐같같같같같같같같같같같같� 같같같같같같같같같같같� #0 Fastnet IRQ: 9 Port:D000 별같같같같같같같같같같같같� 같같같같같같같같같같같픔컴컴컴컴컴컴컴컴컴컴컴컴컴컴캘같같같같같같같같같같같같같 같같같같같같같같같같같� Configuration test : PASS 별같같같같같같같같같같같같� 같같같같같같같같같같같� I/O test : PASS 별같같같같같같같같같같같같� 같같같같같같같같같같같� ID test : PASS 별같같같같같같같같같같같같� 같같같같같같같같같같같� Internal Loopback Test: PASS 별같같같같같같같같같같같같� 같같같같같같같같같같같� External Loopback Test: PASS 별같같같같같같같같같같같같� 같같같같같같같같같같같� Interrupt test : _ 별같같같같같같같같같같같같� 같같같같같같같같같같같� 별같같같같같같같같같같같같� 같같같같같같같같같같같훤袴袴袴袴袴袴袴袴袴袴袴袴袴袴暠같같같같같같같같같같같같같 같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같 같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같 같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같 같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같 같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같 같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같 같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같 같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같 ESC to Exit Figure 1 - PCI Adapter Test Screen This screen will present you with a Testing Report to indicate the result of each test conducted. It will also indicate the Adapter has Passed or failed the test. 3.2 When the network function test is running, the PCI Adapter Test Screen as shown in Figure 2 will be displayed. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴커 � 32-bit PCI-bus Ethernet Adapter Network Testing Program � � Version 2.00 Release Date: May. 24, 1995 � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴켸 같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같 같같같같같같같같같같같�袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴뺐같같같같같같같같같같같같� 같같같같같같같같같같같� #0 Fastnet IRQ: 9 Port:D000 별같같같같같같같같같같같같� 같같같같같같같같같같같픔컴컴컴컴컴컴컴컴컴컴컴컴컴컴캘같같같같같같같같같같같같같 같같같같같같같같같같같� Configuration test : PASS 별같같같같같같같같같같같같� 같같같같같같같같같같같� I/O test : PASS 별같같같같같같같같같같같같� 같같같같같같같같같같같� ID test : PASS 별같같같같같같같같같같같같� 같같같같같같같같같같같� Internal Loopback Test: PASS 별같같같같같같같같같같같같� 같같같같같같같같같같같� External Loopback Test: PASS 별같같같같같같같같같같같같� 같같같같같같같같같같같� Interrupt test : PASS 별같같같같같같같같같같같같� 같같같같같같같같같같같� Network Function Test : OFF 별같같같같같같같같같같같같� 같같같같같같같같같같같훤袴袴袴袴袴袴袴袴袴袴袴袴袴袴暠같같같같같같같같같같같같같 같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같 �袴袴袴袴袴袴袴袴袴袴袴� Node ID: [ xx xx xx xx xx xx ] 袴袴袴袴袴袴袴袴袴袴袴敲 � Tx Count : 0 Packets Rx Count : 0 Packets � � CRC Error : 0 � � ALG Error : 0 � � COLLISION : 0 � � Time : 0 Seconds Performance: 0.000e+000 BPS � 훤袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴暠 Press to Reset Counters, to Toggle ON/OFF, to Exit Figure 2 - PCI Adapter Test Screen with Network Function Test Running There are three function keys which can be used with the DIAG.EXE program: To reset all counters which report the real network status. To toggle the network function test ON or OFF. There is a toggle switch which makes the network function test in reverse way. To terminate and return to the Adapter Selection Screen. The real network status report displays the TX count, RX count and two errors CRC and ALG are shown on the Test Screen. The Time that is accumulated by this program and the Performance which is calculated by this program are also shown on the Test Screen. After you press the key once, the network function test now is entering into the 'ON' condition, that is, TX count is going to increase quickly (single station). And if there is more than one station are running DIAG with network function test 'ON' on your network system (multiple stations), then RX count is also increasing quickly to reflect the real network traffic. The Test Screen layout given in Figure 3 will be shown on your screen while there is only one station running DIAG program. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴커 � 32-bit PCI-bus Ethernet Adapter Network Testing Program � � Version 2.00 Release Date: May. 24, 1995 � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴켸 같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같 같같같같같같같같같같같�袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴뺐같같같같같같같같같같같같� 같같같같같같같같같같같� #0 Fastnet IRQ: 9 Port:D000 별같같같같같같같같같같같같� 같같같같같같같같같같같픔컴컴컴컴컴컴컴컴컴컴컴컴컴컴캘같같같같같같같같같같같같같 같같같같같같같같같같같� Configuration test : PASS 별같같같같같같같같같같같같� 같같같같같같같같같같같� I/O test : PASS 별같같같같같같같같같같같같� 같같같같같같같같같같같� ID test : PASS 별같같같같같같같같같같같같� 같같같같같같같같같같같� Internal Loopback Test: PASS 별같같같같같같같같같같같같� 같같같같같같같같같같같� External Loopback Test: PASS 별같같같같같같같같같같같같� 같같같같같같같같같같같� Interrupt test : PASS 별같같같같같같같같같같같같� 같같같같같같같같같같같� Network Function Test : OFF 별같같같같같같같같같같같같� 같같같같같같같같같같같훤袴袴袴袴袴袴袴袴袴袴袴袴袴袴暠같같같같같같같같같같같같같 같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같 旼컴컴컴컴컴컴컴컴컴컴컴 Node ID: [ xx xx xx xx xx xx ] 컴컴컴컴컴컴컴컴컴컴컴커 � Tx Count : 4711 Packets Rx Count : 0 Packets � � CRC Error : 0 � � ALG Error : 0 � � COLLISION : 0 � � Time : 5 Seconds Performance: 1.326e+007 BPS � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴켸 Press to Reset Counters, to Toggle ON/OFF, to Exit Figure 3 - Test Screen with Network Function Test 'ON' (Single Station) When the Diagnostic Test run detects a problem, it will indicate the status in the Diagnostic Test status report; displays the possible cause of failure and the suggested solution to the problem. Figure 4 presents a layout of this screen. 旼컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴커 � 32-bit PCI-bus Ethernet Adapter Network Testing Program � � Version 2.00 Release Date: May. 24, 1995 � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴켸 같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같 같같같같같같같같같같같�袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴뺐같같같같같같같같같같같같� 같같같같같같같같같같같� #0 Fastnet IRQ: 9 Port:D000 별같같같같같같같같같같같같� 같같같같같같같같같같같픔컴컴컴컴컴컴컴컴컴컴컴컴컴컴캘같같같같같같같같같같같같같 같같같같같같같같같같같� Configuration test : PASS 별같같같같같같같같같같같같� 같같같같같같같같같같같� I/O test : PASS 별같같같같같같같같같같같같� 같같같같같같같같같같같� ID test : PASS 별같같같같같같같같같같같같� 같같같같같같같같같같같� Internal Loopback Test: PASS 별같같같같같같같같같같같같� 같같같같같같같같같같같� External Loopback Test: PASS 별같같같같같같같같같같같같� 같같같같같같같같같같같� Interrupt test : FAIL 별같같같같같같같같같같같같� 같같같같같같같같같같같� 별같같같같같같같같같같같같� 같같같같같같같같같같같훤袴袴袴袴袴袴袴袴袴袴袴袴袴袴暠같같같같같같같같같같같같같 같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같같 旼컴컴컴컴컴� Description : 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴커 � Please check your IRQ setting in PCI configuration, check if IRQ � � number is conflict with other adapters. And run DIAG.EXE again. � � Please also check the cabling system if it is connected correctly. � � If all the IRQ setting is OK and cabling system is correct too, � � contact your dealer. � 읕컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴켸 ESC to Exit Figure 4 - PCI Adapter Test Screen showing failed test components 4. Test Fail Messages Possible causes of failures and suggested solutions during the diagnostics test are listed below : �袴袴袴袴袴袴袴袴袴袴箇袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴敲 � Test Result � Suggested Solution � 勁袴袴袴袴袴袴袴袴袴誥袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴� � Configuration � 1. Check PCI BIOS setup about PCI � � Test Fail � adapter . � � � 2. Contact your dealer. � 勁袴袴袴袴袴袴袴袴袴誥袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴� � I/O Test Fail � 1. Check the parameter with PCI � � � adapter in BIOS setup is correct � � � or not. � � � 2. Check if you are now running � � � EMM386.EXE. If your EMM386.EXE � � � has a version earlier than 4.49 � � � or you use the HIGHSCAN flag, � � � it can not handle properly � � � DWORD accesses and may cause � � � the I/O Test to fail. � � � 3. Contact your dealer. � 勁袴袴袴袴袴袴袴袴袴誥袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴� � ID Test Fail � 1. ID checksum error. � � � 2. Contact your dealer. � 勁袴袴袴袴袴袴袴袴袴誥袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴� � Internal Loopback � 1. Contact your dealer. � � Test Fail � � 勁袴袴袴袴袴袴袴袴袴誥袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴� � External Loopback � 1. Check your cables, connectors � � Test Fail � and terminators(Coaxial cables). � � � 2. Check if you have selected the � � � right medium type. � � � 3. Check if you are using a cross- � � � over cable, if you use cross- � � � over cable, you may not pass the � � � external loopback test, yet you � � � can pass this test just press � � � ENTER key. � � � 4. Contact your dealer. � 勁袴袴袴袴袴袴袴袴袴誥袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴� � Interrupt Test � 1. Check IRQ setting in your PCI � � Fail � configuration of your computer. � � � 2. Check your cables, connectors � � � and terminators(Coaxial cables). � � � 3. Check your BIOS configuration � � � Setting, re-setup your � � � Adapter. � � � 4. Contact your dealer. � 勁袴袴袴袴袴袴袴袴袴誥袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴� � Network Function � 1. Check cables, connectors, and � � Test : � board connections. � � Receive Test Fail � 2. Re-install the adapter board. � � (Rx packet count � 3. Reset the stations and run the � � not running) � DIAG program in various � � � sequence to decide which � � � adapter board is defective. � � � 4. Contact your dealer. � 훤袴袴袴袴袴袴袴袴袴菰袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴袴� - END -