ISA NE-Series Ethernet Adapter
	      NDIS DRIVER FOR LAN SERVER INSTALLATION
	      =======================================

The drivers named ETHNE contained in the directory
NDIS conform to the Network Driver Interface
Specification (NDIS) defined by Microsoft/3Com.

DOS LAN Requester
-----------------
1. Insert the IBM LAN Support Program (LSP)
	Version 1.30 (or 1.31) Diskette into your
	floppy drive (drive A: or B:).
2. Type the following from your DOS prompt
	and press <Enter>:
		A:>dxmaid
3. The screen will display the IBM logo. Press
	<Enter> twice until the "Environment Information"
	appears onscreen.
4. Responds to the screen prompts, specifying the
	following values for each field:

	Use the <Space Bar> to toggle between choices:

	  Configuration for this computer?	    Yes
	  Use existing configuration information?   Yes
	  Do you have adapter option diskettes?     Yes
	  Are you configuring for two adapters?     No
	  Do you need 802.2 interface support?	    Yes

	Type change as needed to drive and directory information below:

	  Source for LSP			   A:\
	  Target for new configuration		   C:\lsp

5. Make sure that the values given above are correct.
	Press <Enter> to store your choices.
6. Insert the Driver Diskette in your source drive.
	Specify the path and press <Enter> to proceed.
	Examples:
	A:\NDIS\DOS
	B:\NDIS\DOS
7. Upon pressing <Enter> the necessary drives
	from the Driver Diskette are copies onto you
	target directory in the hard disk.
8. Follow screen instructions to complete the
	process. Simply pressing <Enter> for each
	screen display will select the default options.
	Press <Enter> three times, until you reach
	the display prompting you to insert the LSP
	diskette.
9. Insert the LSP diskette as prompted. Press
	<Enter> to acknowledge completion of the action.
10. A screen showing the current configuration detected
	will be displayed. It should show the ISA NE-Series
	Ethernet Adapter and the protocols already
	selected (i.e., "IBM IEEE 802.2" and
	"IBM OS/2 NETBIOS").
11. Press <F4>.  to save the new configuration. This
	completes the LSP installation.

	Note:

	You should have defined in your CONFIG.SYS the
	minimum of 20 files, i.e. FILES=20, to run the
	software properly. Change the FILES line using
	the text editor if needed.

	If installing LSP for the first time, you should
	complete the installation by typing install and
	following the further instructions on screen.

12. Use a text editor to edit the CONFIG.SYS file.
	Specify at least 20 file in the FILES= line.
	Modify it to the following:
	FILES=20
13. Save the configuration and reset your computer.
14. Insert the DOS LAN Requester Install Diskette 1
	into your floppy drive.
15. Type the following and press <Enter>:
		INSTALL    <Enter>
16. The IBM logo will again appear on the screen.
	Press <Enter> to move on to the next screen.
17. Follow screen instructions, pressing <Enter>
	to move from screen-to-screen until you
	are prompted to indicate the pathname of
	the DOS LAN Requester directory.

	TIP: After the IBM logo appears on the screen,
	press <Enter> twice to reach this screen.

18. Specify the pathname for the DOS LAN Requester
	directory (C:\DOSLAN is the default). Then
	press <Enter> to continue.
19. The program will ask you for the services
	that you require.
20. Highlight the appropriate option. Select
	either "Send messages" or "Send, View, Edit,
	and Log message" option.

	TIP: Normally, second option "Send, View, Edit
	and Log message" is selected.

21. Specify the PC's ID and domain ID.
	The domain ID is the domain server ID; it should
	be the same for all workstations of the network.
22. Follow screen prompts to complete the installation.

OS/2 LAN Server
---------------
1. Copy ETHNE.OS2 and NDISOS2.NIF files from your
	Driver diskette (\NDIS\OS2) to c:\ibmcom\macs.
2. Click the OS/2 LAN Service icon.
3. Select "Installation and configuration." The IBM
	logo should appear onscreen.
4. Click <OK>.
5. Select <Advance> and press <Enter>.
6. Select "Install or Configuration this Workstation."
7. Select server type, adding a server or domain controller.
	The "install or remove" selections should appear.
8. Select "Configure a component."
10. Click the "Configure" button.
11. Select "Configure workstation."
12. Select "ISA NE-Series Ethernet Adapter" when
	prompted to identify you Network Adapter.
	Then click the <Add> button.
13. Select "802.2" from the list and
	click the <Add> button.
14. Select IBM NETBIOS from the list and
	click the <Add> button
15. Select <OK> to confirm all selections.
16. Follow screen instructions to complete the process,
	selecting <OK> to accept default selections.
17. Continue pressing <OK> until your screen
	prompts you to backup old CONFIG.SYS and
	AUTOEXEC.BAT and create a new CONFIG.SYS
	and AUTOEXEC.BAT. Also select <OK> to
	confirm this.
18. Installation is complete now. Reset your
	PC by turning it off and on.


----
All trademarks or brand names mentioned are properties
of their respective companies.

===End===