October 1995 IN-220P Series Ethernet Card Setup/Diagnostic and AUTOInstall programs ========================================= Copyright (c) 1995 by Infotel Corporation. All rights reserved. ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º Setup/Diagnostic program º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ SETUP.EXE is the setup and diagnostic program for the IN-220P famliy ethernet cards. It allows you not only to test the state of the Ethernet cards, but also the cable connections. To run the program, insert the IN-220P Series driver program diskette #1 in a disk drive and execute one of the following commands: SETUP SETUP /F Run the setup program with the /F switch (SETUP /F) only if the card's EEPROM data has been corrupted or if you experience any other difficulty when running the program without the /F switch. You can also configure the card in non-interactive mode by using the /D switch (SETUP /D). The SETUP program will automatically read the text file SETUP.DAT located in the same directory. The following is an example: Connector Type UTP --------> Setting media type. I/O Base Address 0x300 --------> Set I/O base address Interrupt Number 5 --------> Set Interrupt number PNP Enable --------> Enable PnP function Note: 1. The 'Enable/Disable PnP function' is used only with IN220P Series. 2. Setup will only change the setting that appears in SETUP.DAT, and other setting will not be changed. 3. If any setting about boot ROM (ROM Size or ROM Address) appeared, boot ROM will be set to 'Enable'. Otherwise it will set to 'Disable'. 4. If connector type is not configured, the driver will automatically detect the active media connector. IN-220P Series Adapter parameter file table (SETUP.DAT) ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ KEYWORDS ³ AVAILABLE SELECTIONS ³ ÆÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍØÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͵ ³ Connector Type ³ UTP, BNC, AUI ³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ Interrupt ³ 3, 4, 5, 9, 10, 11, 12, 15 ³ ³ Number ³ ³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ I/O Base ³ 200H,220H,240H,260H ³ ³ Address ³ 280H,2A0H,2C0H,2E0H ³ ³ ³ 300H,320H,340H,360H ³ ³ ³ 380H,3A0H,3C0H,3E0H ³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ ROM Size ³ 8K/16K ³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ PNP ³ Enable/Disable ³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ³ ROM Address ³ C0000h C4000h C8000h CC000h, ³ ³ ³ D0000h,D4000h,D8000h,DC000h ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º Brief Introduction to the IN220P Series Setup Programs º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ 1. The files for setup and diagnostics: \INSTALL\README.DOC : Description on how to use the setup programs \INSTALL\SETUP.EXE : SETUP main program \INSTALL\DIAG.EXE : IN-220P Series basic diagnostic program \INSTALL\FORCE.EXE : IN-220P PnP force setup program \INSTALL\IPXODI.COM : IPX protocol driver for ODI stack \INSTALL\NETDIAG.EXE : IN-220P PnP network diagnostic program \INSTALL\LSL.COM : Link support layer for ODI stack \INSTALL\DE22X.COM : IN-220P Series ODI driver \INSTALL\NET.CFG : IN-220P Series configuation program \INSTALL\SETUP_D.EXE : SETUP /D program \INSTALL\SETUP.DAT : Parameter data file 2. Four major different functions of SETUP are listed in the main menu: Auto Configuration Program auto-configure your IN-220P Series Ethernet card. Such as connector type, I/O base address, interrupt number, and remote boot function. * Not support in IN220P Series. Setup Configuration In this section numerous parameters must be specified manually (connector type, I/O, IRQ etc.) Adapter Basic Diagnostics Check the card components and cabling for proper operation. Network Diagnostic This section of setup provides advanced diagnostics using one master and several slave stations for testing the network. 3. SETUP lets you configure the hardware settings of IN-220P Series Ethernet card. You have the following options to view/change: Main Menu Options : =================== 1> Set up Configuration 2> Adapter Basic Diagnostic 3> NetWork Diagnostic Viewed items: Your Current Configuration <1> Node ID <2> Bus Mode <3> Card Type Viewed/Changed items: Set up Configuration <1> Connector Type <2> I/O Base Address <3> Interrupt Number <4> Remote Boot ROM Size/Base Memory Address ------------------------------------------------------------------------------ ****************************************************************************** ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º Detailed Description of IN220P Setup Programsº ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ The following is the setup program's main menu: ÉÍÍÍÍÍ Main Menu ÍÍÍÍÍÍ» º Auto Setting Configuration º º Setup Configuration º º Adapter Basic Diagnostics º º Network Diagnostics º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ 1. Auto Setting Configuration. Select option for automatic configuration. The program will automatically select a working configuation for the adapter. Includes connector type, I/O base address, interrupt number, and remote boot function. 2. Use the Setup Configuration option to manually configure your IN-220P series card. Here you specify settings for connector type, I/O base address, interrupt number, and whether or not to enable the remote boot function. 3. The Adapter Basic Diagnostics option checks the major components of the card and cabling to ensure proper operation. 4. The Network Diagnostic option performs a live transmission test for checking the card's network functionality. This test requires that LSL.COM, IN220P.COM and IPXODI.COM be located in the same directory as the setup program. SETUP CONFIGURATION MENU ------------------------ ÚÄÄÄÄÄÄÄÄÄ Setup Configuration ÄÄÄÄÄÄÄÄÄÄÄ¿ ³ ³ ³ Connector Type ------> UTP (RJ-45) ³ ³ I/O Base Address ----> 300H ³ ³ Interrupt Number ----> 3 ³ ³ Plug and Play -------> Disable ³ ³ Remote Boot ---------> Disable ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ 1. The Connector Type setting lets you specify the connector to be used with your IN-220P series card. 2. The I/O Base Address setting lets you specify the address through which your microprocessor communicates with your card. 3. The Interrupt Number or IRQ setting is used by your card to make a request for service from the microprocessor. 4. The Plug and Play setting only appears is using IN220P Series. It allows you to enable/disable the plug and play function of your card. 5. The Remote Boot setting allows you to use the remote boot function of your card. * To use the remote boot function, a boot ROM must be installed on the card. 6. The Boot ROM Address setting indicates the starting memory address for the boot ROM. (When Boot ROM is enabled) 7. The Boot ROM Size setting indicates the memory size for the boot ROM. (When Boot ROM is enabled) ADAPTER BASIC DIAGNOSTICS ------------------------- The Adapter Basic Diagnostic option lets you run a test for checking your IN-220P Series Ethernet card. The following items are tested: 1. Current I/O Base Address 2. DC-DC Convert, Oscillator, Crystal T7213 3. EEPROM 4. LAN Setup Registers 5. Memory 6. LAN Controller Functions 7. Cable Connection 8. Loopback Mode ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Adapter Diagnostic ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º Node Address : 00 80 C8 00 00 00 º º I/O Base Address : 300H º º Connector Type : BNC (Thin Coax) º º Interrupt Number : 15(16-bit) º ÇÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Cycle ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĶ º Current I/O Base Address ................... Pass º º DC-DC Convert, Oscillator, Crystal T7213 ... Pass º º EEPROM ..................................... Pass º º LAN Setup Registers ........................ Fail º º Memory ..................................... Unknown º º LAN Controller Functions ................... Unknown º º Cable Connection ........................... Unknown º º Loopback Mode Testing ...................... Unknown º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ NETWORK DIAGNOSTICS ------------------- ÉÍÍ Advanced Diagnostics ÍÍÍ» º Setup as a master station º º Setup as a slave station º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ The Network Diagnostic must have one master station. If you want to use this workstation as a master, choose "Setup as a master station". The other station must act as a slave station. To use this workstation as a slave, select "Setup as a slave station". Before running this network diagnostic, copy LSL.COM, IPXODI.COM, IN220P.COM, and NET.CFG to the same directory as the setup program. Slave and Master workstations must have the same frame type as specified in net.cfg. MASTER STATION ÉÍÍÍÍÍÍ Master Station ÍÍÍÍÍÍ» º Waiting Sending Receiving º º \ \ \ º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ SLAVE STATION ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Slave Station ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º Node Address : 00 80 C8 00 00 02 º º I/O Base Address : 300H Test started at : 20:06:10 º º Interrupt Number : 15(16-bit) Current time : 20:10:50 º º Connector Type : BNC (Thin Coax) º ÇÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĶ º º º Transmit Packet Length .................................. 1234 º º Transmit Packet Counter ................................. 1111 º º Transmit Time Out Counter ............................... 0 º º º º Received Packet Length .................................. 1234 º º Received Packet Counter ................................. 1111 º º Received Error Counter .................................. 0 º º No Response Counter ..................................... 0 º º Data Mismatch Counter ................................... 0 º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ