71
0,   Invalid
1,   parameter ignored
2,   Warning
3,   ERROR
4,   No Auto 16/4 ISA Adapters found in this computer
5,   IO address
6,   interrupt level
7,   ROM address
8,   RAM address
9,   NetWare directory
10,  Windows directory
11,  maximum frame size
12,  NetWare Client parameter(s) specified without NetWare directory
13,  NetWare parameter(s) will be ignored.
14,  Card will be inactive.
15,  Configuration complete.
16,  Insert disk 1 and press Enter
19,  No valid configuration found, restoring original configuration.
21,  IO address in conflict.
22,  Interrupt level in conflict.
23,  RAM address in conflict.
24,  ROM address in conflict.
25,  8 bit adapter bus width set for 16 bit machine
26,  Bus width in conflict
27,  Store failed, restoring original configuration
28,  No Help Available
29,  --- Press any key to continue, <ESC> to exit ---
30,  --- Current Adapter Settings ---
31,  Adapter MAC Address
32,  Enabled
33,  Disabled
34,  Configuration
35,  I/O Address
36,  Interrupt
37,  RAM Address
38,  RAM Size
39,  ROM Address
40,  Remote IPL
41,  Token-Ring data rate
42,  Auto Sense data rate
43,  Adapter bus width
44,  Primary
45,  Alternate
46,  This setting in conflict
47,  Insufficient disk space exists to complete installation.
48,  At least one of the following files is write-protected
49,  These files must be un-protected for installation to succeed.
50,  Insufficient files can be opened in order to complete installation
51,  This problem can be remedied by adding:
52,  FILES=20
53,  To your CONFIG.SYS and re-booting your machine.
54,  Node Address
55,  Invalid IO address, parameter ignored.
56,  Invalid interrupt level, parameter ignored.
57,  Invalid ROM address, parameter ignored.
58,  Invalid RAM address, parameter ignored.
59,  Invalid RAM Size, parameter ignored.
60,  Invalid NetWare directory.
61,  Invalid Windows directory.
62,  Invalid maximum frame size, parameter ignored.
63,  Invalid Node Address, parameter ignored.
64,  PnP Configuration, parameter ignored.
65,  Plug and Play
66,  Manual
67,  Card State
68,  Active
69,  Inactive
70,  MicroCode Level
!EXTENDEDHELP
 Usage: TOOLNAME <options>...                                           v

 The available options are:

 /FAST=CFGONLY
           The Configuration-Only fastpath option should be used without other
           parameters, since all other configuration options will be automat-
           ically chosen by the program.  With this option, the card will be
           configured but no other software will be installed.

 /PNP=Y OR /PNP=N
           This option will set the adapter for Plug and Play Configuration
           or Manual Configuration.

 /IO=<####>
           This option will specify the Hex IO address (A20 or A24) of your
           adapter.  If the IO port is invalid, the parameter will be ignored.

 /INT=<##> This option will specify the interrupt level (3, 9, 10 or 11) of
           your adapter.  If the interrupt level specified is unavailable, the
           parameter will be ignored.  ignored.

 /ROM=<#####>
           This option will specify the Hex ROM address (C8000-DE000) of your
           adapter.  This address should be on an 8K boundary within the range
           shown.  If the ROM address specified is invalid, the parameter will
           be ignored.

 /RAM=<#####>
           This option will specify the Hex RAM address (C0000-DE000) of your
           adapter.  This address should be on the boundary /RAMSIZE parameter
           (default 16K).  If the RAM address specified is specified by the
           invalid, the parameter will be ignored.

 /RAMSIZE=<##>
           This option will specify the RAM size in KBytes (8, 16, 32, or 64)
           for your adapter.  If the RAM size specified is not one of the
           listed sizes, the parameter will be ignored.

 /BUSW=<##>
           This option will specify the bus width (8 or 16) of your adapter.
           For optimal performance on a 16 bit computer, the bus width should
           also be set to 16.

 /RIPL=Y OR /RIPL=N
           This option will either enable or disable Remote IPL for your
           adapter.

 /RS=<##>  This option will specify the ring speed (4 or 16) of your adapter.

 /AUTO=Y OR /AUTO=N
           This option will either enable or disable your adapter's ability to
           Auto Sense the ring speed of your ring.  Auto Sense sets the proper
           ring speed for your adapter if you connect to different networks at
           different times.

 /VIEW     View the current settings of the adapter.  VIEW should be
           used without any other options.

 /?, /H, or /HELP
           Display extended help. Specify no options for abbreviated help.
!USAGE
Usage: TOOLNAME <options>...                                           v
 /FAST=CFGONLY - allow all options to be automatically chosen, configure only
 /PNP=Y or /PNP=N - Plug and Play Configuration / Manual Configuration
 /IO=<###> - specify Hex IO address (A20 or A24)
 /INT=<##> - specify interrupt level (3, 9, 10 or 11)
 /ROM=<#####> - specify Hex ROM address (C8000-DE000)
 /RAM=<#####> - specify Hex RAM address (C0000-DE000)
 /RAMSIZE=<##> - specify RAM size in KBytes (8, 16, 32, or 64)
 /BUSW=<##> - specify bus width (8 or 16)
 /RIPL=Y or /RIPL=N - enable/disable Remote IPL
 /RS=<##> - specify ring speed (4 or 16)
 /AUTO=Y or /AUTO=N - enable/disable Auto Sense
 /VIEW - view the current configuration