MKMSGFNFX?mt%Yt 0@VdwW\&k H s  U          # & ) , / 2 5 8 ; > A D G J M P S V Y \ _ b e h k n q t w I j  J z 9]  "%(+.147:=@CFILORUX[^adgjmpsvy|  !$'*-0369<?BEHKNQTWZ]`cfilorux{~*Z0g?BEHKNQTWZ]`cfilorux{~  #nfx.msgI2.40 I Compaq NetFlex-3 / Netelligent %1 NDIS 2.02 driver. Copyright 1997 Compaq Computer Corporation. All rights reserved. IDriver version %1. I%1 is managing %2 controllers. IScanning for NetFlex-3 / Netelligent controllers. IControllers located: %1. IDriver managed controller list: ISlot %1: %2 Interface not controlled by driver. ISlot %1: %2 (IRQ %3, I/O %4, Address: %5). I Max requests: %1 I Max multicasts: %1 I Transmits: %1 I Receives: %1 I Connector type: %1 I Duplex: %1 I Media Speed: %1 I SQE: %1 I ThunderLAN device revision: %1 ? ? ? I Error in reading CPQNET.CFG I Open failed or could not find CPQNET.CFG I Invalid entry in CPQNET.CFG I Reason : Unit %1 is already a partner in another pair ? I Reason : Units %1 and %2 are dissimilar I CPQNET : Cannot configure units %1 and %2 as partners I CPQNET : Failure in unit %1 detected on %2 I CPQNET : Unit %1 recovered from failure on %2 I CPQNET : Failure in unit %1 detected on %2. Switching to unit %3 I CPQNET : Primary has recovered. Switching back to %1 from %2 on %3 I Reason : A unit cannot be paired with itself I Reason : unit %1 is not present in the system I Insufficient number of entries in CPQNET.CFG I Excess number of entries in CPQNET.CFG I CPQNET : Failed to Initialize the Resource Manager I CPQNET : Resource Allocation for IRQ Failed I CPQNET : Resource Allocation for IO Port Failed I CPQNET : Failed to Register the Adapter with the Resource Manager ? CPQNET : Failed to set the adapter in Power Down mode ? CPQNET : Hardware not supported for Power Management ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? WNo controllers found in system. %1 terminating. WController excluded by command line override. WUnsupported ThunderLAN revision. WNo module entry in PROTOCOL.INI. ECould not allocate adequate resources. EDriver initialization failure. EFailed to register with PROTMAN. EInvalid interrupt value: %1. EFailed to acquire interrupt request line %1 from operating system. W%1: Incorrect value type for keyword: %2. W%1: Unrecognized PROTOCOL.INI keyword: %2. WSlot %1: No burned in Node Address in EEPROM. WSlot %1: Invalid configuration data in EEPROM. WUnsupported PHY module detected. EAuto Media Speed detection not supported with 100Base-TX Full Duplex. ESlot %1: UnKnown Physical Module ESlot %1: Error in Physical Module WSlot %1: MediaSpeed defaults to : %2 WSlot %1: Duplex defaults to : %2 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? I%1: Slot: %2 %3 bound to module: %4. ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? WSlot: %1 %2 Adapter Check (%3): Undefined error (no message). WSlot: %1 %2 Adapter Check (%3): Parity error. WSlot: %1 %2 Adapter Check (%3): Bus error. WSlot: %1 %2 Adapter Check (%3): Acknowledge error. WSlot: %1 %2 Adapter Check (%3): Acknowledge overflow error. WSlot: %1 %2 Adapter Check (%3): Receive list error. WSlot: %1 %2 Adapter Check (%3): Transmit list error. WSlot: %1 %2 Adapter Check (%3): Transmit timeout error. ? ? ? ? ? ? ? ? ? ? ? ? WSlot: %1 %2 Network link has been restored. WSlot: %1 %2 Network link is down. WSlot: %1 %2 Request (%3) failure: %4. ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?