		 Windows for Workgroups Installation file        
		 ========================================

				Section 1
				=========

	The installation kit for Windows for Workgroups is comprised of eight 
diskettes.  During the installation of diskette #8, the network environment 
will be configured.  At one point you will be asked to select a Network 
Adapter to install. At this time please select:

		   Unlisted or Updated Network Adapter

After that has been selected you will be told to:

		   Insert unlisted, updated or
		   vendor-provided network driver disk in

Remove diskette #8 from the floppy drive and insert this distribution media. 
At the prompt, type the path where the appropriate OEMSETUP.INF file is 
located as follows:

       A:\WINWGRP\ISA          (if the adapter is being installed
						as an ISA device)
				- or -

       A:\WINWGRP\EISA         (if the adapter is being installed
						as an EISA device)

	NOTE:  DO NOT INCLUDE THE FILENAME AS PART OF THE PATH !!!

Once the file OEMSETUP.INF is loaded, the installation process will display 
that you have selected a "DEC EtherWORKS 3/TURBO Ethernet Adapter". Select 
"OK" to proceed with the installation.

      The installation process will now ask for the updated or vendor-provided
PROTMAN.DOS file. At this point insert diskette #8 once again to load the file.
At the prompt please type the path (e.g. A:\) to your floppy drive. After this 
has completed the installation process will ask:

		     Insert a disk with the updated or
		     vendor-provided EWRK3.DOS file in

At this point remove diskette #8 and insert this distribution media. At the
prompt type:

			    A:\NDIS\DOS

	NOTE:  DO NOT INCLUDE THE FILENAME AS PART OF THE PATH !!!

and press "OK". The installation will now ask for the vendor-provided VNB.386 
file. Remove this distribution media from the diskette drive and insert 
diskette #8. At the prompt please type the path (e.g. A:\) to your floppy 
drive and press "OK". Once this has been completed a screen will appear with 
the following information:

	 Windows Setup recommends the following settings for your 
	 network adapter.

	 Interrupt(IRQ)                                    5
	 Base I/O Port(hex)                                0x300 
	 Base Memory Address(hex)                          0xD000

(If EISA OEMSETUP is used 0x7C00 will appear for the Base I/O Port setting)
Please change any settings necessary, according to your PC's operating 
environment. At this time you may also enter "Advanced..." mode. You also 
have the opportunity to change the following options:

	 MemoryMode, Size of Memory Address Region         (default 2)
	 Diagnostics,  1=ON | 0=OFF                        (default 1)

******************************************************************************
* Note:  If MemoryModes of either 32 or 64 are configured(default is 2).     *
*        Only use the following Memory Address values during the Windows     *
*        for Workgroups installation:                     *
*                                                                            *
*        MemoryMode range of 32 -> A000,A800,B000,B800,C000,C800,            *
*                                  D000,D800,E000,E800,F000,F800             *
*        MemoryMode range of 64 -> A000,B000,C000,D000,E000,F000,            *
*                                                                            *
*  Please make sure that any settings that are selected during the Windows   *
*  for Workgroups installation procedure *MATCH* settings that are currently *
*  configured for on the EtherWORKS 3 module. Please use the NICSETUP        *
*  utility to determine or alter these settings.                             *
******************************************************************************

   Once you are comfortable with your EtherWORKS 3 settings select "Continue" 
and proceed with the installation. A last box will appear entitled "Compatible
Networks". At this point you will need to select your specific Network Type.

				Section 2
				=========

 Note: For users who have *PREVIOUSLY* ADDed the EtherWORKS 3 card to 
       Windows for Workgroups and are trying to update their setup with 
       a newer EtherWORKS 3 OEMSETUP.INF file. First you need to enter 
       Windows for Workgroups and REMOVE the adapter. Then exit Windows 
       for Workgroups and delete the previously created OEMn.INF(where n 
       is a number) for the EtherWORKS 3 card that resides in your 
       \WINDOWS\SYSTEM directory. Type out the file(s) OEMn.INF individually 
       and delete any file that contains EtherWORKS 3 adapter information 
       before re-installing the new EtherWORKS 3 OEMSETUP.INF file found 
       on this distribution media. 

   If Windows for Workgroups has already been installed using a Network 
Adapter other than an EtherWORKS 3 card. The following procedure can be used 
to add the card to your system:

     1) Click on the MAIN icon.
     2) Click on the CONTROL PANEL icon.
     3) Click on the NETWORK icon.
     4) Click on the ADAPTERS button.
     5) Click on the REMOVE button to delete currently used Network Adapter
     6) Click on the ADD button
     7) Select Unlisted or Updated Network Adapter then click on OK.
     8) Insert this distribution media into your floppy drive and enter the 
	path to where the appropriate OEMSETUP.INF file is:


	  A:\WINWGRP\ISA          (if the adapter is being installed
						   as an ISA device)
				    - or -

	  A:\WINWGRP\EISA         (if the adapter is being installed
						  as an EISA device)

	   NOTE:  DO NOT INCLUDE THE FILENAME AS PART OF THE PATH !!!

	   Click on OK to proceed with the installation.

     9) You will now be asked to:

		     Insert a disk with the updated or
		     vendor-provided EWRK3.DOS file in

	At this point please enter:

			    A:\NDIS\DOS

	NOTE:  DO NOT INCLUDE THE FILENAME AS PART OF THE PATH !!!

	Click on OK to proceed with the installation.

    10) You will now see a box showing:

	       Your network adapter is configured as follows:

	   Interrupt(IRQ)                                 5
	   Base I/O Port(hex)                             0x300 
	   Base Memory Address(hex)                       0xD000

(If EISA OEMSETUP is used 0x7C00 will appear for the Base I/O Port setting)
Please alter any of these settings as is necessary according to your PC's 
operating environment. At this time you may also enter "Advanced..." mode. 
You also have the opportunity to change the following options:

	   MemoryMode, Size of Memory Address Region      (default 2)
	   Diagnostics,  1=ON | 0=OFF                     (default 1)

******************************************************************************
* Note:  If MemoryModes of either 32 or 64 are configured(default is 2).     *
*        Only use the following Memory Address values during the Windows     *
*        for Workgroups installation:                                        *
*                                                                            *
*        MemoryMode range of 32 -> A000,A800,B000,B800,C000,C800,            *
*                                  D000,D800,E000,E800,F000,F800             *
*        MemoryMode range of 64 -> A000,B000,C000,D000,E000,F000,            *
*                                                                            *
*  Please make sure that any settings that are selected during the Windows   *
*  for Workgroups installation procedure *MATCH* settings that are currently *
*  configured for on the EtherWORKS 3 module. Please use the NICSETUP        *
*  utility to determine or alter these settings.                             *
******************************************************************************
