@@@@HELP_HELP
@BGeneral Help@B
@S------------@S

@BF1@B                 Bring up a help screen
@BF3@B                 Exit the @BXsetup@B utility
@BENTER@B              Select
@BESC@B                Cancel the action

@BSPACE@B              Mark an Item
@BBACKSPACE@B, @BCTRL-H@B  Delete to the left within an editor field
@BDELETE@B, @BCTRL-D@B     Delete character under the cursor in an edit field
@BLEFT@B, @BCTRL-B@B       Move the cursor left
@BRIGHT@B, @BCTRL-F@B      Move the cursor right
@BUP@B, @BCTRL-P@B         Move the cursor up
@BDOWN@B, @BCTRL-D@B       Move the cursor down
@BHOME@B, @BCTRL-A@B       Move the cursor to the beginning of the line
@BEND@B, @BCTRL-E@B        Move the cursor to the end of the line


@@@@MAIN_MENU
 @BMain Menu@B
 @S---------@S

 The chart below represents the information gathered from the current valid
 configuration files. Use the cursor keys to navigate around and press
 @BENTER@B if you want to change an item.

 After you have configured everything correctly, use @BF3@B to exit & save the
 new setup. If something goes wrong you can abort the utility instead
 of saving the changes.
@@@@BOARD_MENU
 @BBoard Selection@B
 @S---------------@S

 Use this menu to select your board. Use the cursor keys to navigate around
 and press @BENTER@B when you want to select a new board.

 If a board does not show a memory size, we assume 1MB is available
 on the graphics board.  The Server may fail if you have less than
 1MB on the board, unless explictely listed as being supported.
@@@@BOARD_WARNING
              @BWarning@B

The board you have chosen requires
a non-standard memory location:

            @B0x%08x@B

If you are running on a system with
@BISA@B, @BEISA@B or @BVL@B bus, please verify
that the graphics board has been
configured correctly.
@@@@MONITOR_MENU
 @BMonitor Selection@B
 @S-----------------@S

 Use this menu to select your monitor. Use the cursor keys to navigate around
 and press @BENTER@B when you want to select a monitor.

 Please be careful about the selection, since the X-Server uses the monitor
 information to compute the correct display parameters. If your specific
 Monitor is not listed, consult your documentation about the technical
 details and choose one of the @BMultiFrequency@B entries that matches best.
@@@@VIDEO_MENU
 @BVideo Mode Selection@B
 @S--------------------@S

 This checkboard allows you to change all video parameters in a single step.
 Use the cursor keys to navigate around and press @BSPACE@B if you want to
 mark/unmark a item.

 Note, that only a subset of the entries might be selectable depending on
 the choice of graphics board and monitor. Also there is a relationship
 between the number of colors and the possible resolutions.  

 It is possible to have more than one resolution selected at the same time.


       @BResolution            Desktop              Colors@B 
       @S----------------------------------------------------------------@S
@@@@SAVE_MENU
The name of the configuration file
(The X-Server will normally look for 
@B$HOME/.Xaccel.ini@B and @B/etc/Xaccel.ini@B):
@@@@ABORT_POPUP
Do you really want to exit ?

 @BF2@B  = exit without saving
 @BF3@B  = save and exit
 @BESC@B = cancel
@@@@DEVICE_MENU
Please enter the name of the
device for the mouse:
@@@@RGB_MENU
Please enter the full path of the RGB text file.
This file MUST be the unprocessed text version and
not one of the various binary file formats:
@@@@FONT_MENU
Please enter a comma separated list of paths, where 
the X-Server should look for fonts by default:
@@@@XQUEUE_ERROR
              @BXqueue Error@B

You cannot use the Xqueue input handling
on a @B%s@B Operating System.
@@@@XQUEUE_WARNING
              @BXqueue Warning@B

Your @B%s@B Operating System does support
Xqueue input handling. Unless you are really
absolutely sure that you need to use a direct
device handling we strongly suggest that you
select again @BXqueue@B.
@@@@SAVE_ERROR
              @BERROR@B

Failed to save Setup to specified path:

 @B%s@B

Please respecify the path correctly.
@@@@EOF
