   Personal NetWare

   Personal NetWare* Installation Notes for Intel's 
   EtherExpress(TM) PRO/10 LAN Adapter
   ===============================================

   Location of Driver:     \DOS\EPROODI.COM


   General Installation
   --------------------
      The installation procedure will transfer files to a specific directory 
      on the workstation and create or modify existing configuration files 
      to fit your specific needs.  The installation utility INSTALL.EXE is 
      located on Personal NetWare's "Installation + Utilities 1" disk. 
  
   Installation Procedure
   ----------------------
      Run INSTALL.EXE from the "Installation + Utilities 1" Disk.

      The Personal NetWare Install program screen will appear.  You must
      complete each of the questions.  These options are specific to your
      needs.

      1. Step #1 asks you for your name, company name, and serial number 
         of  your copy of Personal NetWare.

      2. Step #2 gives you the option to load support files for MS Windows 
         and tells you the disk space requirements. You will also have an 
         option to change the directory where the Personal NetWare files 
         will be copied. The default directory is C:\NWCLIENT.  You can 
         specify another directory if you desire.

      3. Step #3 asks you to select a Primary Network Interface Card. From 
         the list of drivers select "OEM Supplied Driver".

         NOTE:  Do not select Intel EtherExpress ISA family. This driver 
         is for the EtherExpress16 not for the EtherExpress PRO/10. 

      4. Step #4 will ask you to insert the diskette containing the driver 
         files. Insert the EtherExpress PRO/10 diskette into drive A: and 
         specify the source path for driver files as A:\DOS.

      5. Step #5 will let you specify if you want to Share This Computers 
         Resources.

      6. Step #6 will let you specify a User Name for this computer.

      7. Step #7 will let you specify what Novell NetWare Servers are 
         available on your network. 

      8. Step #8 will allow you to configure Optimization / Network 
         Management. Refer to your Personal NetWare Manual to decide 
         what options you need.

      9. Step #9 is Configure Primary Interface Card. Specify the PORT 
         address that was configured in SoftSet2 for the EtherExpress PRO/10
         adapter. The default port address is 300. Select the Ethernet 
         frame type you want to use. The default frame is Ethernet_802.2.

      10.Step #10 is to accept all of the configuration parameters. If 
         everything is configured correctly then accept the configuration 
         and start the installation. The Personal NetWare installation
         will now prompt you for the installation diskettes as needed.   

      11.Step #11 is the final step. You will be prompted to insert the 
         driver diskette for the third party software driver. Insert the 
         EtherExpress PRO/10 diskette into drive A: and specify the path 
         to copy the files from as A:\DOS. 


   Hints and Tips
   --------------

      1. NET.CFG Options:
         PORT - This is the base I/O address of the adapter.  Verify 
         setting in SoftSet2.  

         INT - The system IRQ for the adapter to use.  This option is only 
         used as a reminder for which IRQ the board is set for.  It does 
         not cause the driver to override the EEPROM contents.  The 
         EtherExpress PRO/10 adapters support IRQ's 2, 3, 5, 10, 11. 

      2. Be sure to add LASTDRIVE=Z to your CONFIG.SYS file for the 
         network mappings to work properly.

      3. Below is a sample NET.CFG and STARTNET.BAT. These files 
         are located in the C:\NWCLIENT directory by default.

         STARTNET.BAT:

         @ECHO OFF
         SET NWLANGUAGE=ENGLISH
         C:
         CD C:\NWCLIENT
         LH SHARE /F:10240 /L:200
         LH LSL
         LH EPROODI
         LH IPXODI
         LH SERVER
         VLM
         CD \
         C:\NWCLIENT\NET LOGIN


         NET.CFG:

         Link driver EPROODI
            PORT 300
            FRAME Ethernet_802.3
            FRAME Ethernet_802.2
            FRAME Ethernet_II
            FRAME Ethernet_SNAP

        Netware DOS Requester
            FIRST NETWORK DRIVE = F
            NETWARE PROTOCOL = PNW,BIND,NDS
            VLM = NMR.VLM
            VLM = WSSNMP.VLM
            VLM = WSTRAP.VLM
            VLM = WSREG.VLM
            VLM = WSASN1.VLM
            VLM = PNWTRAP.VLM
            VLM = PNWMIB.VLM




   * Third-party trademarks are the property of their respective owners
